Thermtrack

Home

Product details FAQs Resources Installation Gallery Contact & ordering

Product information

Thermitrack cameras
General specifications
(All models)
Hardware
Viewing area 2.3 to 4.4m square on floor typical over recommended mounting height range.
Power supply : 9-15VDC, 200mA max
Interface: RS422 full-duplex. (Custom options : RS232, DMX+RS232, dual DMX.)
Connection : 6 way 3.5mm plug-in terminal block (plug supplied). Camden Electronics CTB92HD/6 
Recommended cable : single CAT5 or CAT6 for data and power up to 20m. For longer runs, a seperate power cable or local DC supply may be required to minimise voltage drop.

Resolution  
Thermal images :  16x16 pixels, 256 grey levels scalable from internal 4096 level greyscale with programmable filtering  for noise reduction and programmable X/Y orientation flip.
Tracking : 12 bit (0..4095) X/Y position resolution. Achievable resolution and accuracy will be dependent on target characteristics and operating environment.

Internal software functionality
Frame rate: 30 frames/sec.
Baudrates 9600, 19k2, 38k4,50k, 76k8,100k, 115k2,230k4, 250k, 460k8, 500k, 961k2,1Mbaud,   1 or 2 stop bits.

User-selectable data outputs can include :
Tracking co-ordinates of single target.
Tracking co-ordinates of all targets in view.
Thermal image data
Status.

Data can be sent on request from the host, or configured to sent autonomously at programmable intervals, allowing the camera to be used as an 'output-only' device.

Networking capability : Up to 9 cameras may be connected in a ring configuration to pass data from multiple cameras to a single serial (RS422/RS232/USB) port.

wpe2E0.jpg (44296 bytes)

Thermitrack 60
Order code TT60

Standard indoor unit with 60 degree field of view for 2.5 to 4.5 metre mounting height.

110mm dia x 50mm high. Removable twist+lock mounting base for easy installation.

Operating temperature range 0 to 40ºC

 

 

 

wpe1AB.jpg (15679 bytes)

Thermitrack 40
Order code TT40

Narrow-angle indoor unit with 40 degree field of view for 4 to 7 metre mounting height.

110mm dia x 50mm high. Removable twist+lock mounting base for easy installation.

Operating temperature range 0 to 40ºC


wpe1AA.jpg (13246 bytes)

Thermitrack Outdoor 60
Order code TT60-OD

Thermitrack Outdoor 40
Order code TT40-OD

Thermitrack Outdoor 20
Order code TT20-OD

 

Outdoor unit IP65 with 60 degree field of view for 2.5 to 4.5 metre mounting height.

Outdoor unit IP65 with 40 degree field of view for 4 to 7 metre mounting height

Outdoor unit IP65 with 20 degree field of view for 7 to 13 metre mounting height

Rugged diecast aluminium housing. Four M16 threaded side cable entries, two each side.
Breather vent to avoid condensation buildup.

130x125x80mm.Operating temperature range -20 to +40ºC

Image on left shows TT40-OD. Lens detail on others shown below

wpe1E.jpg (4874 bytes)TT60-OD

wpe1D.jpg (6115 bytes)TT20-OD

Accessories
RS422 to USB interface
Order code TTUSB

USB Interface

Interfaces Thermitrack  RS422 to USB, with internal power converter to power one camera from the USB port.`
USB drivers pre-configured to optimise throughput. See resources page for driver info.

External power connector (2.1mm power jack) allows connection of optional external 12V power supply for running multiple cameras, or where the USB port cannot provide sufficient current (max 400mA required from USB port).

Supplied with 6 way plug-in terminal block and USB A-B cable.

LEDs indicate power and data.

PSU not included. (recommended PSU if required Rapid Electronics stock no. 85-3112

RS422 to RS232 interface
Order code TTRS232

RS232 Interface

Interfaces Thermitrack RS422 to standard RS232 9 way DF connector on PC etc. Power connection via 2.1mm power jack connector. (RS422 interface requires power even if camera is powered from elsewhere).

LED indicates incoming data.

Supplied with 6 way plug-in terminal block and 12V 1A plug-in power supply to run up to 4 cameras.

USB Quick-start kit
Order code TTQSU
Kit contains :

Thermitrack 60 Camera
USB interface with USB A-B cable
Ready-terminated 10 metre  cable to camera.

RS232 quick-start kit
Order code TTQSR
Kit contains :

Thermitrack 60 Camera
RS232 interface with 12V plug-in power supply (UK/EU/US interchangeable plugs).
Ready-terminated 10 metre  cable to camera .

Ready-terminated cable (10 metre)
Order code TTCAB10
Cable with 6-way pluggable terminal block connector at each end. (PVC - LSZH available to special order)